67 mm to Inches
Convert 67 millimeters to inches — instant, accurate, and easy
The Answer
Browse metric rulers on Amazon.
📄 Free printable mm to inches chart (PDF) — every mm from 1 to 300.
How to Convert 67 mm to Inches
To convert 67 millimeters to inches, divide the millimeter value by 25.4. This is because one inch equals exactly 25.4 millimeters — a standard defined by international agreement.
The Calculation
Applying the formula to 67 mm:
Result Summary for 67 mm
- Decimal inches: 2.6378″
- Fractional inches: 2 41/64″ (nearest 1/64)
- Feet and inches: 0 ft 2.64 in
Reference Table — Values Near 67 mm
| Millimeters | Decimal Inches | Fractional Inches |
|---|---|---|
| 64 mm | 2.5197″ | 2 33/64″ |
| 65 mm | 2.5591″ | 2 9/16″ |
| 66 mm | 2.5984″ | 2 19/32″ |
| 67 mm | 2.6378″ | 2 41/64″ |
| 68 mm | 2.6772″ | 2 43/64″ |
| 69 mm | 2.7165″ | 2 23/32″ |
| 70 mm | 2.7559″ | 2 3/4″ |
67 mm in Other Units
Millimeters convert cleanly into every other length unit. Here is 67 mm expressed seven different ways — useful when a drawing, spec sheet or supplier quotes a unit other than inches.
| Unit | 67 mm equals |
|---|---|
| Centimeters (cm) | 6.7 cm |
| Meters (m) | 0.067 m |
| Inches (in) | 2.6378 in |
| Feet (ft) | 0.2198 ft |
| Yards (yd) | 0.07327 yd |
| Thousandths of an inch (mil) | 2,637.8 mil |
| Typographic points (1/72 in) | 189.92 pt |
How Accurate Is Each Fraction of 67 mm?
67 mm equals 2.6378″ (rounded to four decimal places). Any fraction is a further rounding of the full-precision value, so each one carries a small error. This table shows the closest fraction at each common denominator and how far it actually sits from 67 mm.
| Rounded to | Fraction | Decimal | Fraction vs. original |
|---|---|---|---|
| Nearest 1/2″ | 2 1/2″ | 2.5000″ | −3.500 mm (below original) |
| Nearest 1/4″ | 2 3/4″ | 2.7500″ | +2.850 mm (above original) |
| Nearest 1/8″ | 2 5/8″ | 2.6250″ | −0.325 mm (below original) |
| Nearest 1/16″ | 2 5/8″ | 2.6250″ | −0.325 mm (below original) |
| Nearest 1/32″ | 2 5/8″ | 2.6250″ | −0.325 mm (below original) |
| Nearest 1/64″ | 2 41/64″ | 2.6406″ | +0.072 mm (above original) |
For woodworking, DIY and general workshop use, 2 5/8″ is the practical choice — it lands within 0.4 mm of 67 mm. For machining, toolmaking or CAD, use the decimal value 2.6378″ rather than any fraction.
FAQ About 67 mm to Inches
How many inches is 67 mm?
67 millimeters equals 2.6378 inches (rounded to 4 decimal places), or approximately 2 41/64″ (nearest 1/64 inch).
How accurate is the 67 mm to inches conversion?
The conversion of 67 mm to 2.6378 inches uses the exact definition 1 inch = 25.4 millimeters; the four-decimal result is rounded, so it is approximate.
Can I convert 67 mm to feet?
Yes. 67 millimeters equals approximately 0 ft 2.64 in.
📏 Need to measure 67mm accurately?
A steel ruler marked in millimeters makes it easy to find 67 mm (≈ 2.6378″). See current options:
→ See precision steel rulers on Amazon
Or step up to a digital caliper for finer work →
As an Amazon Associate, we earn from qualifying purchases at no extra cost to you.