27 mm to Inches
Convert 27 millimeters to inches — instant, accurate, and easy
The Answer
Browse digital calipers on Amazon.
📄 Free printable mm to inches chart (PDF) — every mm from 1 to 300.
How to Convert 27 mm to Inches
To convert 27 millimeters to inches, divide the millimeter value by 25.4. This is because one inch equals exactly 25.4 millimeters — a standard defined by international agreement.
The Calculation
Applying the formula to 27 mm:
Result Summary for 27 mm
- Decimal inches: 1.0630″
- Fractional inches: 1 1/16″ (nearest 1/64)
- Feet and inches: 0 ft 1.06 in
Reference Table — Values Near 27 mm
| Millimeters | Decimal Inches | Fractional Inches |
|---|---|---|
| 24 mm | 0.9449″ | 15/16″ |
| 25 mm | 0.9843″ | 63/64″ |
| 26 mm | 1.0236″ | 1 1/32″ |
| 27 mm | 1.0630″ | 1 1/16″ |
| 28 mm | 1.1024″ | 1 7/64″ |
| 29 mm | 1.1417″ | 1 9/64″ |
| 30 mm | 1.1811″ | 1 3/16″ |
27 mm in Other Units
Millimeters convert cleanly into every other length unit. Here is 27 mm expressed seven different ways — useful when a drawing, spec sheet or supplier quotes a unit other than inches.
| Unit | 27 mm equals |
|---|---|
| Centimeters (cm) | 2.7 cm |
| Meters (m) | 0.027 m |
| Inches (in) | 1.0630 in |
| Feet (ft) | 0.0886 ft |
| Yards (yd) | 0.02953 yd |
| Thousandths of an inch (mil) | 1,063 mil |
| Typographic points (1/72 in) | 76.54 pt |
How Accurate Is Each Fraction of 27 mm?
27 mm equals 1.0630″ (rounded to four decimal places). Any fraction is a further rounding of the full-precision value, so each one carries a small error. This table shows the closest fraction at each common denominator and how far it actually sits from 27 mm.
| Rounded to | Fraction | Decimal | Fraction vs. original |
|---|---|---|---|
| Nearest 1/2″ | 1″ | 1.0000″ | −1.600 mm (below original) |
| Nearest 1/4″ | 1″ | 1.0000″ | −1.600 mm (below original) |
| Nearest 1/8″ | 1 1/8″ | 1.1250″ | +1.575 mm (above original) |
| Nearest 1/16″ | 1 1/16″ | 1.0625″ | −0.013 mm (below original) |
| Nearest 1/32″ | 1 1/16″ | 1.0625″ | −0.013 mm (below original) |
| Nearest 1/64″ | 1 1/16″ | 1.0625″ | −0.013 mm (below original) |
For woodworking, DIY and general workshop use, 1 1/16″ is the practical choice — it lands within 0.4 mm of 27 mm. For machining, toolmaking or CAD, use the decimal value 1.0630″ rather than any fraction.
FAQ About 27 mm to Inches
How many inches is 27 mm?
27 millimeters equals 1.0630 inches (rounded to 4 decimal places), or approximately 1 1/16″ (nearest 1/64 inch).
How accurate is the 27 mm to inches conversion?
The conversion of 27 mm to 1.0630 inches uses the exact definition 1 inch = 25.4 millimeters; the four-decimal result is rounded, so it is approximate.
Can I convert 27 mm to feet?
Yes. 27 millimeters equals approximately 0 ft 1.06 in.
📏 Need to measure 27mm accurately?
Digital calipers typically display readings to 0.01 mm resolution, enough to check 27 mm (≈ 1.0630″). See current options:
→ See digital calipers on Amazon
Read our digital calipers buying guide →
As an Amazon Associate, we earn from qualifying purchases at no extra cost to you.