A tape measure looks simple until you need to read a mark like “7 and 11/16.” This guide explains exactly what every line on an imperial tape means, how the metric side works, and how to switch between the two without mistakes. Keep our printable inches to mm chart next to you while you read.
The Two Sides of a Tape Measure
Dual-scale tape measures usually show inches on the top edge and centimeters and millimeters on the bottom edge. Many tapes are inch-only or metric-only. Before you measure, check which edge you are reading — mixing them up is the most common mistake people make.
Reading the Inch Side
Each inch on a standard tape is divided into 16 equal parts, so the smallest gap between two lines is 1/16 of an inch (about 1.59 mm). Some tapes add 1/32″ marks along part of the blade. The trick is that the lines are different lengths so you can recognize them quickly:
- Inch lines are the longest and are numbered.
- Half-inch (1/2″) line is the next longest, exactly halfway between two numbers.
- Quarter-inch lines (1/4″, 3/4″) are shorter again.
- Eighth-inch lines (1/8″, 3/8″, 5/8″, 7/8″) are shorter still.
- Sixteenth lines are the shortest — every other line.
Read 11/16 Inch on an Enlarged Scale
For 7 11/16 inches, count from the 7-inch mark, not from the start of the blade. The exact conversion is (7 + 11/16) × 25.4 = 195.2625 mm. Reporting 195.26 mm rounds that value; reporting 195 mm rounds it further.
Check the Cost of Choosing a Nearby Mark
For an 80 mm dimension, the nearest 1/16-inch mark is 3 1/8 inches. That mark equals 79.375 mm, so it is 0.625 mm short. The next mark, 3 3/16 inches, equals 80.9625 mm and is 0.9625 mm long. If the job allows only ±0.5 mm, neither mark meets that tolerance: use the metric scale or a suitable finer measuring tool.
Every 1/16″ Mark in One Inch
| Mark | Decimal inches | Millimeters (rounded) | Line length |
|---|---|---|---|
| 1/16″ | 0.0625″ | 1.59 mm | Shortest (1/16″) |
| 1/8″ | 0.1250″ | 3.18 mm | Medium (⅛″) |
| 3/16″ | 0.1875″ | 4.76 mm | Shortest (1/16″) |
| 1/4″ | 0.2500″ | 6.35 mm | Long (¼″) |
| 5/16″ | 0.3125″ | 7.94 mm | Shortest (1/16″) |
| 3/8″ | 0.3750″ | 9.53 mm | Medium (⅛″) |
| 7/16″ | 0.4375″ | 11.11 mm | Shortest (1/16″) |
| 1/2″ | 0.5000″ | 12.70 mm | Half-inch line (next longest) |
| 9/16″ | 0.5625″ | 14.29 mm | Shortest (1/16″) |
| 5/8″ | 0.6250″ | 15.88 mm | Medium (⅛″) |
| 11/16″ | 0.6875″ | 17.46 mm | Shortest (1/16″) |
| 3/4″ | 0.7500″ | 19.05 mm | Long (¼″) |
| 13/16″ | 0.8125″ | 20.64 mm | Shortest (1/16″) |
| 7/8″ | 0.8750″ | 22.23 mm | Medium (⅛″) |
| 15/16″ | 0.9375″ | 23.81 mm | Shortest (1/16″) |
| 1″ | 1.0000″ | 25.40 mm | Inch line (longest) |
How to Read a Measurement Step by Step
- Find the last full inch number before the end of the object — say 7.
- Count the lines past that number to where the object ends. If it ends on the 11th small line, that is 11/16″.
- Simplify if possible: an even count reduces (for example 8/16 = 1/2, 12/16 = 3/4). 11/16 cannot be reduced.
- Put it together: 7 11/16″, which is 7.6875″ or 195.26 mm.
A faster habit: look at the length of the line the object ends on. If it is the medium-long line between the half and the inch, it is 3/4″; if it is the shortest line just before that, it is 11/16″.
Reading the Metric Side
The metric side is simpler because everything is based on tens. Numbered lines are centimeters, and each centimeter is split into 10 millimeters. The half-centimeter (5 mm) line is usually a little longer to help you count. A reading of “19 and 5 small lines” is 19.5 cm, which is 195 mm.
Work in metric trades is often given in millimeters only, because “195 mm” is harder to misread than “19.5 cm.” Note that 195 mm (7.677″) is very close to the 7 11/16″ reading above, but not identical: 7 11/16″ is 195.26 mm.
Converting Between Inches and Millimeters
The conversion is exact: 1 inch = 25.4 mm.
- Inches to mm: multiply by 25.4. Example: 3/8″ = 0.375 × 25.4 = 9.525 mm (9.53 mm rounded).
- mm to inches: divide by 25.4. Example: 80 mm ÷ 25.4 ≈ 3.1496″ (rounded), which is about 3 1/8″ on the tape.
When a metric size does not land on a 1/16″ line — which is most of the time — write down the decimal value or use the nearest fraction and note that it is approximate. For example, 51 mm is 2.0079″: very close to 2″, but exactly 2″ is 50.8 mm. See our mm to inches chart for every millimeter from 1 to 100, then every 10 mm up to 300.
Worked Examples: Metric Sizes on an Inch Tape
Use these examples to practise reading fractions and checking how far the marked size differs from the original millimeter dimension.
- 12 mm: compare 15/32 inch with half an inch
- 70 mm: find the point just beyond 2 3/4 inches
- 80 mm: choose between nearby tape fractions
- 200 mm: mark 7 7/8 inches and check the rounding difference
- 300 mm: compare a metric ruler with 12 inches
Tape Measure Tips That Prevent Mistakes
- The hook moves on purpose. The metal hook at the end slides by exactly its own thickness so that inside and outside measurements are both accurate. Do not bend it back.
- Keep the blade straight. A sagging or angled tape reads long. For long runs, have someone hold the end or lock the blade.
- For inside measurements (inside a cupboard or window frame), add the length of the tape body printed on its case, or measure from a clear mark such as 10 cm and subtract it.
- Look straight down at the mark, not from an angle, to avoid reading the wrong line.
- Measure twice, cut once — and write the unit next to the number.
Frequently Asked Questions
What is the smallest mark on a tape measure?
On most imperial tapes it is 1/16 inch (1.5875 mm). On the metric side it is 1 millimeter.
What are the black diamonds on a tape measure?
They mark 19.2-inch (about 19 3/16-inch) spacing, used for laying out floor joists and trusses. Five 19.2-inch spaces equal 96 inches (8 feet).
Why are some numbers highlighted in red every 16 inches?
16 inches is a common spacing between wall studs in North American framing, so tapes highlight 16, 32, 48 inches and so on.
Is 25 mm the same as 1 inch?
No. 1 inch is exactly 25.4 mm, so 25 mm is 0.9843″ — close, but 0.4 mm short. That difference matters for pipes, fittings and holes.
Related: Inches to MM chart (printable) · MM to Inches chart (printable) · MM to inches converter · Best 25ft tape measures
Sources and Checking
- NIST Guide to the SI, Appendix B.8 (1 inch = 0.0254 m exactly)
Published by Johnson, who runs mmintoinches.com. Every value in this guide was recalculated from 1 inch = 25.4 mm and checked against the sources below on 9 October 2026. Found a mistake? Email support@mmintoinches.com with the page and the value.