29 mm to Inches
Convert 29 millimeters to inches — instant, accurate, and easy
The Answer
Browse digital calipers on Amazon.
📄 Free printable mm to inches chart (PDF) — every mm from 1 to 300.
How to Convert 29 mm to Inches
To convert 29 millimeters to inches, divide the millimeter value by 25.4. This is because one inch equals exactly 25.4 millimeters — a standard defined by international agreement.
The Calculation
Applying the formula to 29 mm:
Result Summary for 29 mm
- Decimal inches: 1.1417″
- Fractional inches: 1 9/64″ (nearest 1/64)
- Feet and inches: 0 ft 1.14 in
Reference Table — Values Near 29 mm
| Millimeters | Decimal Inches | Fractional Inches |
|---|---|---|
| 26 mm | 1.0236″ | 1 1/32″ |
| 27 mm | 1.0630″ | 1 1/16″ |
| 28 mm | 1.1024″ | 1 7/64″ |
| 29 mm | 1.1417″ | 1 9/64″ |
| 30 mm | 1.1811″ | 1 3/16″ |
| 31 mm | 1.2205″ | 1 7/32″ |
| 32 mm | 1.2598″ | 1 17/64″ |
29 mm in Other Units
Millimeters convert cleanly into every other length unit. Here is 29 mm expressed seven different ways — useful when a drawing, spec sheet or supplier quotes a unit other than inches.
| Unit | 29 mm equals |
|---|---|
| Centimeters (cm) | 2.9 cm |
| Meters (m) | 0.029 m |
| Inches (in) | 1.1417 in |
| Feet (ft) | 0.0951 ft |
| Yards (yd) | 0.03171 yd |
| Thousandths of an inch (mil) | 1,141.7 mil |
| Typographic points (1/72 in) | 82.2 pt |
How Accurate Is Each Fraction of 29 mm?
29 mm equals 1.1417″ (rounded to four decimal places). Any fraction is a further rounding of the full-precision value, so each one carries a small error. This table shows the closest fraction at each common denominator and how far it actually sits from 29 mm.
| Rounded to | Fraction | Decimal | Fraction vs. original |
|---|---|---|---|
| Nearest 1/2″ | 1″ | 1.0000″ | −3.600 mm (below original) |
| Nearest 1/4″ | 1 1/4″ | 1.2500″ | +2.750 mm (above original) |
| Nearest 1/8″ | 1 1/8″ | 1.1250″ | −0.425 mm (below original) |
| Nearest 1/16″ | 1 1/8″ | 1.1250″ | −0.425 mm (below original) |
| Nearest 1/32″ | 1 5/32″ | 1.1563″ | +0.369 mm (above original) |
| Nearest 1/64″ | 1 9/64″ | 1.1406″ | −0.028 mm (below original) |
For woodworking, DIY and general workshop use, 1 9/64″ is the practical choice — it lands within 0.4 mm of 29 mm. For machining, toolmaking or CAD, use the decimal value 1.1417″ rather than any fraction.
FAQ About 29 mm to Inches
How many inches is 29 mm?
29 millimeters equals 1.1417 inches (rounded to 4 decimal places), or approximately 1 9/64″ (nearest 1/64 inch).
How accurate is the 29 mm to inches conversion?
The conversion of 29 mm to 1.1417 inches uses the exact definition 1 inch = 25.4 millimeters; the four-decimal result is rounded, so it is approximate.
Can I convert 29 mm to feet?
Yes. 29 millimeters equals approximately 0 ft 1.14 in.
📏 Need to measure 29mm accurately?
Digital calipers typically display readings to 0.01 mm resolution, enough to check 29 mm (≈ 1.1417″). See current options:
→ See digital calipers on Amazon
Read our digital calipers buying guide →
As an Amazon Associate, we earn from qualifying purchases at no extra cost to you.